Eaton transmission fault code f

The UltraShift PLUS transmission is equipped with an Electric Clutch Actuator (ECA) that controls the position of the clutch assembly. The ECA operates on a non-switched battery power supply. Fault Code 66 indicates battery power to the ECA is outside of the acceptable ECA operating range.

ZF Freedomline Transmission Parts Book PB 0127. ZF Meritor 13 Speed Manual Transmission Operator Manual TP 90192. ZF Meritor 9 10 Platform G Transmission. ZF Meritor Sureshift Transmission Fault Code Diagnostics. ZF S5 42 47 47M Service Manual.The Fuller Advantage transmission is equipped with Hill Start Aid (HSA) which prevents roll-back and roll-forward while launching on grades that are 1% and greater. ... (TECU) and ABS Module communicate over the J1939 Data Link and control the HSA function. Fault Code 22 sets if the TECU loses communication with the ABS or the ABS communicates ...Fault Code 66 – ECA Battery Voltage Detection. The following preconditions must be met before the system detects the fault: Hybrid Control Module (HCM) ignition voltage is …"F" flashes in gear display. Service light flashes (if equipped). Engine may not crank. Transmission may not attempt to shift. Transmission may not confirm neutral. Engine may have to be shut down with transmission still in gear. 1. Transmission Electronic Control Unit (TECU)Roadranger: Eaton, Dana and other trusted partners providing the best products and services in the industry, ensuring more time on the road. More time on the road TM Fuller® Automated Transmissions Fault Codes Description 11 No ECU. Operation Test 12 Improper ECU Configuration 13 J1939 Control Device 14 Invalid Shift Lever Voltage 16 High ... 6. Two digit fault codes will be displayed in the gear display. Record the codes. A one or two second pause separates each stored code, and the sequence automatically repeats after all codes have been flashed. Clearing Fault Codes 1. Start with the key in the 6 TIMESON position.

Record the transmission fault codes, FMIs, occurrences, and timestamps from the Service Activity Report created during the Diagnostic Procedure. If Fault Code 57 is Active with FMI 3, 4 or 5, Go to Step C. ... If Fault Code 57 sets Active during the test drive, contact Eaton at (800) 826-4357 for further diagnostics. ...If Fault Code 19 is Active and Fault Code 16 is Inactive or not set, If any fault became Active while wiggling the 3-Way Connector to the ECA, refer to OEM guidelines for repair or replacement of the ECA Power Harness. If any fault became Active while wiggling the Transmission Harness, replace. If readings are out of range, Pin C (Battery posi ... If Fault Code 64, 66 or 67 is Active, troubleshoot per Fault Code Isolation Procedure Index. If Fault Code 27 FMI 7 is set and a new TECU was not just installed, Go to Step B. If Fault Code 27 FMI 13 is Active, Go to Step F. If Fault Code 27 FMI 13 is Inactive, a Clutch Calibration has been performed. Clear fault codes using ServiceRanger, test ...Fault Code 56 Troubleshooting 1. Record the transmission fault codes, FMIs, occurrences, and timestamps from the Service Activity Report created during the Diagnostic Procedure. Note: Inspect clutch for caging bolts if Fault Code 56 FMI 2 is Active immediately after start up. • If Fault Code 56 is Active with FMI 5, go to Step C.If damage to the ECA side of 2-Way Gen2 ECA Connector is found, replace Electronic Clutch Actuator (ECA) Electronic Clutch Actuator (ECA) Electronic Clutch Actuator (ECA) If no fault codes set Active and vehicle operates properly, test complete. If Fault Code 16 sets Active, contact Eaton at (800) 826-4357 for further diagnostics.Record the transmission fault codes, FMIs, occurrences, and timestamps from the Service Activity Report created during the Diagnostic Procedure. If Fault Code 57 is Active with FMI 3, 4 or 5, Go to Step C. ... If Fault Code 57 sets Active during the test drive, contact Eaton at (800) 826-4357 for further diagnostics. ...

If Fault Code 68 is Inactive, test complete. If TECU is improperly mounted or not secure, mount or secure TECU properly. If Fault Code 68 is Active, replace Transmission Electronic Control Unit (TECU). Perform procedure with ServiceRanger or Operator Triggered Procedure contained within TRSM0940. Go to Step V.#owneroperator #dammitboy #TruckerNews#truckingpay #truckdriver #reefertrucking #freight #reeferfreight #trucks #trucker #CDLOTR #Cash_is_KingTRKBUY CASH ME... If non-transmission fault codes related to the J1939 Data Link are present, troubleshoot per OEM guidelines. If transmission Fault Code 35, Fault Code 36 or Fault Code 64 are present, troubleshoot per Fault Code Isolation Procedure Index. If Fault Code 26 is Active or Inactive, Go to Step B Transmission codes? How do you pull codes on your automatic transmission? In this video we cover how to pull the blink codes on your Eaton Ultrashift 13 spee...Ensure these pictures are clear and the components are easily visible. Email these pictures to [email protected] and contact Eaton at (800) 826-4357. If no fault codes set Active and vehicle operates properly, test complete. If Fault Code 81 sets Active during the test drive, contact Eaton at (800) 826-4357.

Swiftpaws net worth.

Check for fault codes using ServiceRanger. † If no fault codes set Active and vehicle operates properly, test complete. † If Fault Code 65 sets Acti ve during the test drive, return to transmission specific diagnostic man-ual for extended trouble shooting. † If a fault code other than 65 sets, troubleshoot using appropriate ...Endurant HD automated transmission. The Endurant HD is a lightweight, highly efficient transmission designed for superb driveability in on-highway applications. Sophisticated software allows the engine and transmission to work seamlessly, improving efficiency and performance. Smart features like a transmission fluid pressure sensor help protect ...Fault Code 68: Grade Sensor (TRTS0940) If Fault Code 68 is Inactive, test complete. If TECU is improperly mounted or not secure, mount or secure TECU properly. If TECU is properly mounted and secured, If Fault Code 68 is Inactive, Go to Step V. If Fault Code 68 is Active, replace Transmission Electronic Control Unit (TECU). 3 +200 lbs.-ft. [271 Nm] in top two gears. 4 Will interfere with front mount oil filter. Rear or remote mount oil filter must be utilized. 6 Intermittent torque of up to 750 lb.-ft. at the countershaft is permitted for 5 minutes of each 15 minute PTO duty cycle. Fuller Advantage series automated 10-speed transmission is a legacy AMT from Eaton ...

Eaton Transmission Fault Code F is a diagnostic trouble code (DTC) that is related to the transmission system. It usually indicates an issue with the electronic control module (ECM) or the transmission gear ratio. This code can be generated by a variety of conditions, including an overheated transmission, engine shutdown, or a faulty sensor. ...Eaton Transmission Fault Code list 88, 64, 21, 27, 25, 19, 22, 71, 16, 66 and Eaton Ultrashift Gen 3 Fault Codes in PDFThe data link is a two wire twisted pair with two 120 ohm resistors located in the link. Fault Code 88 will only be set with Hybrid Control Module (HCM) software level 663 and lower. HCM software 671 and greater will set a fault code 111 for the inverter CAN message fault.tone will only sound when the fault is active and the tone will stop when the fault is Inactive. The fault will stay in the gear display until the system is powered down. NOTE: Active codes set during PD Mode will not be stored as Inactive. 7. If a fault is detected, exit PD Mode and troubleshoot the fault code. 8. To exit PD Mode, turn the key ...2017 Kw with a cummins ISX and a eaton ultrashift 18 speed. Model number f0-18e3186-mxp. It is setting a flash code 71. Looking it up in Service ranger I get a ID 560 FMI 11 driveline engaged root cause not known. The truck moves in forward and reverse and will shift gears until 10th gear or so. I do not see this fmi in the troubleshooting ...ZF Freedomline Transmission Parts Book PB 0127. ZF Meritor 13 Speed Manual Transmission Operator Manual TP 90192. ZF Meritor 9 10 Platform G Transmission. ZF Meritor Sureshift Transmission Fault Code Diagnostics. ZF S5 42 47 47M Service Manual.Aug 27, 2021 · Transmission codes? How do you pull codes on your automatic transmission? In this video we cover how to pull the blink codes on your Eaton Ultrashift 13 spee... 3 +200 lbs.-ft. [271 Nm] in top two gears. 4 Will interfere with front mount oil filter. Rear or remote mount oil filter must be utilized. 6 Intermittent torque of up to 750 lb.-ft. at the countershaft is permitted for 5 minutes of each 15 minute PTO duty cycle. Fuller Advantage series automated 10-speed transmission is a legacy AMT from Eaton ...fault issues when there are no Active fault codes present. IMPORTANT: The vehicle will not start in PD Mode. You must turn vehicle key off, and allow the transmission to fully power down to exit PD Mode before the vehicle will start. PD Mode Inactive Fault Codes The following is a list of fault codes that work with PD Mode:... F": The AutoShift has detected an active component code ... Eaton Fuller Transmission Fault Code Fault Code Isolation Procedure Eaton Fuller Transmission Fault ...If active fault code(s) is set, refer to TRTS0990 Procision Troubleshooting Guide. If no active fault codes, select “Clear Eaton Faults” and follow on-screen prompts. 13. Disconnect ServiceRanger. 14. Key off. Warranty Information: Information only The material contained in this bulletin is product improvement information. Eaton Corporation ...If Fault Code 64, 66 or 67 is Active, troubleshoot per Fault Code Isolation Procedure Index. If Fault Code 27 FMI 7 is set and a new TECU was not just installed, Go to Step B. If Fault Code 27 FMI 13 is Active, Go to Step F. If Fault Code 27 FMI 13 is Inactive, a Clutch Calibration has been performed. Clear fault codes using ServiceRanger, test ...

STEP C: Key off. Install (2) 0-100 PSI air pressure gauges in the splitter cover diagnostic ports. Start vehicle and allow air pressure to build to governor cut-off. Release clutch (AutoShift only) to register input shaft speed in the transmission. Turn off engine but leave the key in the ON position. With Shift Control, select reverse (R1 in ...

If Fault Code 58 FMI 5, 6 or 10 is Inactive, Go to Step B. If Fault Code 58 FMI 5, 6, 10 is Active, Go to Step F. If Fault Code 58 FMI 2 is Active or Inactive, Go to Step D. If Fault Code 58 FMI 8, 11 is Active or Inactive, Go to Step ICheck for fault codes using ServiceRanger. † If no fault codes set and vehicle operates properly, test complete. † If Fault Code 63 sets Acti ve during the test drive, return to transmission specific diagnostic manual for extended trouble shooting. † If a fault code other than 63 sets, troubleshoot using appropriate troubleshooting manual ...transmission driver interface device to Upshift or Downshift to the desired gear. Refer to OEM transmission driver interface device instructions. † If vehicle speed is greater than 2 MPH, the transmission system will not allow engagement into a Reverse gear position. Note: The transmission system may automatically override or prevent theFault Code 11 Troubleshooting 1. Record the transmission fault codes, FMIs, occurrences, and timestamps from the Service Activity Report. • If Fault Code 11 is the ONLY CODE Active and present in SAR, replace TECU. Go to Step V. 1. Key off. 2. Reconnect all connectors and verify that all components are properly installed. 3. Key on …Fault Code 65 – ECA Speed Sensor Detection. The following preconditions must be met before the system detects the fault: ECA ignition voltage is greater than 8.5 volts. Fault Code 18 or 87 are Active. Note: When troubleshooting an Inactive code refer to the Product Diagnostic Mode (PDM)Date: December 19, 2018 STEP A: Create a Service Activity Report (SAR). Set vehicle parking brake and chock wheels. Key on with engine off. Connect ServiceRanger. Go to …Eaton Fuller Transmission Fault Code Isolation Procedure The FMI (Failure Mode Identifier) The FMI (Failure Mode Identifier) is used along with the SPN to provide specific information that relates to a diagnostic trouble code (DTC). The FMI may indicate that a problem with an electronic circuit

Jake paul address.

Set my alarm for 5 15.

Fault Code 56 Troubleshooting 1. Record the transmission fault codes, FMIs, occurrences, and timestamps from the Service Activity Report created during the Diagnostic Procedure. Note: Inspect clutch for caging bolts if Fault Code 56 FMI 2 is Active immediately after start up. • If Fault Code 56 is Active with FMI 5, go to Step C.An 88 may appear in the gear display which indicates self testing.The Fuller Advantage transmission is equipped with an auto-neutral function. This function shifts the transmission to neutral when the vehicle is brought to a complete stop while the transmission is in gear and the park brake is set. Fault Code 21 indicates a problem with the Auto-Neutral Park Brake Switch circuit.Conditions to Set Fault Code Inactive. FMI 2: X-Y Rail Position Sensor return voltage signal stays within the 0.5–4.5-volt range for 1 second. FMI 3, 4: Supply voltage stays within the 4.75–5.25 volt range for 1 second. FMI 10: X-Y Rail Position Sensor return voltage signal remains consistent (within ±0.2 volts) while the transmission is ...2017 Kw with a cummins ISX and a eaton ultrashift 18 speed. Model number f0-18e3186-mxp. It is setting a flash code 71. Looking it up in Service ranger I get a ID 560 FMI 11 driveline engaged root cause not known. The truck moves in forward and reverse and will shift gears until 10th gear or so. I do not see this fmi in the troubleshooting ...Do you need help with troubleshooting your Eaton Gen 3 automated manual transmission? Download this comprehensive guide from Weller Truck, the leading provider of remanufactured driveline components. Learn how to diagnose and fix common problems with your transmission system. Fallback When Fault Code 22 is set the following conditions occur: Amber “Check Hybrid” light displays. Fault is stored in HCM memory. If the fault occurs while moving, the operation mode goes into AutoShift only. Electric motor/generator Assist and Regeneration are disabled; however, the high-voltage relays remain powered.If Fault Code 64, 66 or 67 is Active, troubleshoot per Fault Code Isolation Procedure Index. If Fault Code 27 FMI 7 is set and a new TECU was not just installed, Go to Step B. If Fault Code 27 FMI 13 is Active, Go to Step F. If Fault Code 27 FMI 13 is Inactive, a Clutch Calibration has been performed. Clear fault codes using ServiceRanger, test ... ….

An 88 may appear in the gear display which indicates self testing.If Fault Code 64, 66 or 67 is Active, troubleshoot per Fault Code Isolation Procedure Index. If Fault Code 27 FMI 7 is set and a new TECU was not just installed, Go to Step B. If Fault Code 27 FMI 13 is Active, Go to Step F. If Fault Code 27 FMI 13 is Inactive, a Clutch Calibration has been performed. Clear fault codes using ServiceRanger, test ...Unknown General Transmission Fault (SPN 2003 - FMI 31) 2). Open Allison DOC and connect to diagnostic port on Allison Transmission. Read More: How to Connecting ALLISON Transmission using ALLISON DOC Software. Figure 1.3 - DTC and General Information. →No Active DTC's. In this case, there are 4 logged codes: P2723, …Fault Code 11 Troubleshooting 1. Record the transmission fault codes, FMIs, occurrences, and timestamps from the Service Activity Report. • If Fault Code 11 is the ONLY CODE Active and present in SAR, replace TECU. Go to Step V. 1. Key off. 2. Reconnect all connectors and verify that all components are properly installed. 3. Key on …Fault Code 88 – CAN Inverter Message (HCM) Detection. The following preconditions must be met before the system detects the fault: HCM ignition voltage is greater than 7 volts and less than 16 volts. HCM CAN data link fault is Inactive. Note: When troubleshooting an Inactive code refer to the Product Diagnostic Mode (PDM)transmission software versions do not set Fault Code 94. FMI 12: No internal ECA ... 375 © 2018 Eaton Cummins Automated Transmission Technologies. All rights ...Fault Code 71: Unable to Disengage Gear (TRTS0940) If Fault Code 71 FMI 7 is Active or Inactive and/or Fault Codes 27, 33, 34, 51, 52, 61, 63 or 64 are Active or Inactive, troubleshoot per. If any fault sets Active while wiggling the Transmission Harness, replace. If any fault sets Active while wiggling the Power Supply harness, refer to OEM ... Fault Code 68: Grade Sensor (TRTS0940) If Fault Code 68 is Inactive, test complete. If TECU is improperly mounted or not secure, mount or secure TECU properly. If TECU is properly mounted and secured, If Fault Code 68 is Inactive, Go to Step V. If Fault Code 68 is Active, replace Transmission Electronic Control Unit (TECU). FMI 3: TECU detects an open or short to VBATT in the control circuit of the Start Enable Relay for 1 second or greater. FMI 4: TECU detects a short to ground in the control circuit of the Start Enable Relay for 1 second or greater. Fallback When Fault Code 17 is set the following conditions occur: Red “Service” light illuminates and an “F ... Eaton transmission fault code f, Aug 15, 2018 · On this page you can find Eaton Transmission Fault Code 88, 64, 21, 27, 25, 19, 22, 71, 16, 66 And Eaton Ultrashift Gen 3 Fault Codes. See also: Eaton Service Repair Manuals PDF. Eaton Fuller Fault/ Autoshift Ultrashift Codes in PDF. Title. , ZF-FreedomLine Transmission Fault Code Diagnostics and Wiring Diagram (TP-01110) How to Order Tools Specified in This Manual Call ArvinMeritor’s Commercial Vehicle Aftermarket at 888-725-9355 to order Meritor tools. SPX Kent-Moore, 28635 Mound Road, Warren, Michigan, 48092. Call the company’s customer, Permanent Fault Code 71 FMI 11 Procedure . Date: December 19, 2018 STEP A: Create a Service Activity Report (SAR). 1. Set vehicle parking brake and chock wheels. 2. Key on with engine off. 3. Connect ServiceRanger. 4. Go to “Fault Codes”. 5. Verify that the vehicle has an Active Fault Code 71 FMI 11., Permanent Fault Code 71 FMI 11 Procedure . Date: December 19, 2018 STEP A: Create a Service Activity Report (SAR). 1. Set vehicle parking brake and chock wheels. 2. Key on with engine off. 3. Connect ServiceRanger. 4. Go to "Fault Codes". 5. Verify that the vehicle has an Active Fault Code 71 FMI 11., The Fuller Advantage transmission is equipped with Hill Start Aid (HSA) which prevents roll-back and roll-forward while launching on grades that are 1% and greater. ... (TECU) and ABS Module communicate over the J1939 Data Link and control the HSA function. Fault Code 22 sets if the TECU loses communication with the ABS or the ABS communicates ..., Fault Code 19, 64 and 67 PACCAR Vehicles equipped with UltraShift PLUS and Fuller Advantage Transmissions - TAIB0883 (PDF 445 KB, 10/08/2020) , Fault Code 65 – ECA Speed Sensor Detection. The following preconditions must be met before the system detects the fault: ECA ignition voltage is greater than 8.5 volts. Fault Code 18 or 87 are Active. Note: When troubleshooting an Inactive code refer to the Product Diagnostic Mode (PDM), service manager. Associate Degree. 2,429 satisfied customers. Transmissions: i have a eaton fuller tramission ser;k0594308. i have a eaton fuller tramission ser;k0594308 and need to know if a parker pto …, If readings are in range, replace Eaton Push Button Shift Control Device (PBSC) Go to Step V. If no fault codes set Active and vehicle operates properly, test complete. If Fault Code 15 sets Active during test drive, contact Eaton at (800) 826-4357 for further diagnostics. If a fault code other than 15 sets Active, troubleshoot per Fault Code ..., 2016.01.15 © 2016 Eaton. All rights reserved 215 TRTS0930 Fault Isolation Procedures | Fault Code 68 - Grade Sensor Component Identification Transmission ECU, Fault Code 71: Unable to Disengage Gear (TRTS0940) If Fault Code 71 FMI 7 is Active or Inactive and/or Fault Codes 27, 33, 34, 51, 52, 61, 63 or 64 are Active or Inactive, troubleshoot per. If any fault sets Active while wiggling the Transmission Harness, replace. If any fault sets Active while wiggling the Power Supply harness, refer to OEM ..., Record the transmission fault codes, FMIs, occurrences, and timestamps from the Service Activity Report created during the Diagnostic Procedure. Note: Fault Code 36 indicates an issue with communication over the J1939 data link between the Engine ECU and the Transmission TECU. All wiring and pin outs for connectors are OEM proprietary., Roadranger: Eaton, Dana and other trusted partners providing the best products and services in the industry, ensuring more time on the road. More time on the road TM Fuller® Automated Transmissions Fault Codes Description 11 No ECU. Operation Test 12 Improper ECU Configuration 13 J1939 Control Device 14 Invalid Shift Lever Voltage 16 …, • If the fault is detected during PDM mode the gear display will display the active fault/s. The warning tone will only sound when the fault is active and the tone will stop when the fault is inactive. The fault will stay in the gear display until the system is powered down. Active codes set during PDM mode will not be stored as inactive., Fault Code 19, 64 and 67 PACCAR Vehicles equipped with UltraShift PLUS and Fuller Advantage Transmissions - TAIB0883 (PDF 445 KB, 10/08/2020), Eaton Fault Codes list ; 65. 251. 4. Low voltage power supply of electric motors ; 71. 60. 7. Transmission jammed., - Turn key on. Engine cranks and gear display is N (neu-- If problem continues, call 1-800-826-HELP tral), go to Step C. (4357) Fault Code F on gear display, go to Step D. Neutral N on gear display, go to Step B. 2016.01.15 2016 Eaton., Conduit, cable & wire management. Fuel systems, emissions and components. Hose, tubing, fittings and connectors. Hydraulic power packs and accumulators. Industrial controls, drives, automation and sensors. Low-voltage power distribution & control systems. Medium-voltage power distribution & control systems., When you’re shopping for a new car, it’s important to know what type of transmission it has. Knowing the type of transmission can help you make an informed decision about the car and its performance. Fortunately, decoding your car’s transmi..., Additionally, intermittently while driving Fault Code 760, SPN 6146, FMI 15/17 may set Active. Affected Models/Population: Endurant HD: • EEO-xxF112C • EE-xxF111B • EHD-xxF112C-N . Note: If transmission model number is EHD-xxF112C-N with TCM software part number 5516034, contact Eaton Cummins Automated Transmission Technologies at, Mar 25, 2012 · service manager. Associate Degree. 2,429 satisfied customers. Transmissions: i have a eaton fuller tramission ser;k0594308. i have a eaton fuller tramission ser;k0594308 and need to know if a parker pto 4896gsahxa3xd will work … read more. , Go To Fault Codes: a. If Fault Code 27 FMI 7 and/or Fault Code Fault Code 64 FMI 7 is Inactive, clear fault codes, disconnect ServiceRanger, process complete. b. If Fault Code 27 FMI 7 and/or Fault Code Fault Code 64 FMI 7 is Active, go to troubleshooting guide and complet e Fault Code Isolation Procedure. Warranty Information: Information only, Go to Step V. If no fault codes set and the vehicle operates properly, test complete. If transmission Fault Code 76 is Active, contact Eaton at (800) 826-4357. If an engine/vehicle fault code is Active, troubleshoot the fault code per OEM guidelines. Go to Step A., Clearing Fault Codes 1. Start with the key in the ON position. Turn the key OFF and ON six times within five seconds, ending with the key in the ON position. Note: If the codes have been successfully cleared, the service lamp will come on and stay on for five seconds. 2. Turn the key OFF and allow system to power down. OFF ON, STEP 1. Check for Active or Inactive fault code status. Review and follow the Warnings & Cautions. Retrieve Active fault codes and FMIs with ServiceRanger using the 9-Way Diagnostic Connector. 3. Key on and observe the red Push Button “Service” light. If the red “Service” light turns on, go to Step 3., Verify which FMI set. Determine which FMI set for Fault Code 63. If FMI 1 set, contact Eaton at (800) 826-4357 for repair strategy. If FMI 12 set, replace Transmission Electronic Control Unit (TECU). Go to Step V. Key off. Reconnect all connectors and verify that all components are properly installed. , Feb 27, 2023 · February 27, 2023 by Alex Gearhart. Fault Code 88 in Eaton Transmissions indicates a specific malfunction within the transmission system. It’s crucial to address this code promptly as it can lead to significant transmission issues, especially in Kenworth trucks. Regular checks and understanding the code’s implications can prevent potential ... , The Fuller Advantage transmission is equipped with Hill Start Aid (HSA) which prevents roll-back and roll-forward while launching on grades that are 1% and greater. ... (TECU) and ABS Module communicate over the J1939 Data Link and control the HSA function. Fault Code 22 sets if the TECU loses communication with the ABS or the ABS communicates ..., Clearing Fault Codes 1. Start with the key in the ON position. Turn the key OFF and ON six times within five seconds, ending with the key in the ON position. Note: If the codes have been successfully cleared, the service lamp will come on and stay on for five seconds. 2. Turn the key OFF and allow system to power down. OFF ON, direction F or R selected while parking brake engaged transmission in neutral until parking brake is released. CAUTION: vehicle starts to move after release ..., Fault Code 83: Invalid Shift Lever Position (TRTS0980) If lever positions do not match gear display, replace Shift Lever. If lever positions match gear display, test complete. If no fault codes set Active and vehicle operates properly, test complete. If Fault Code 83 sets Active during the test drive, Go to Step A. If a fault code other than 83 ..., STEP C: Key off. Install (2) 0-100 PSI air pressure gauges in the splitter cover diagnostic ports. Start vehicle and allow air pressure to build to governor cut-off. Release clutch (AutoShift only) to register input shaft speed in the transmission. Turn off engine but leave the key in the ON position. With Shift Control, select reverse (R1 in ..., If Fault Code 14 is Inactive, refer to OEM guidelines for repair or replacement of wiring between TECU and analog Shift Lever. Go to Step V. If no fault codes set Active and vehicle operates properly, test complete. If Fault Code 14 sets Active during the test drive, Go to Step A. If a fault code other than 14 sets Active, troubleshoot per ...